SCCP Configuration
After the profiles are set up, both routers should be configured for SCCP. As a reminder,
the SCCP agreement is acclimated for signaling amid Cisco Unified Communications
Manager and the router absolute the DSP resources.
Both routers use their Fast Ethernet 0/1 interface as the SCCP antecedent interface, and the
primary Cisco Unified Communication Manager should be 10.1.1.201. Because Cisco
Unified Communications Manager 4.1 is deployed, this is additionally authentic in the SCCP configuration
on anniversary router to ensure abounding interoperability amid the router and Cisco
Unified Communications Manager.
After the Cisco Unified Communications Manager servers accept been defined, the SCCP
groups can be configured. Again, Fast Ethernet 0/1 is acclimated as the antecedent interface for the
group, and the ahead authentic Cisco Unified Communications Manager is associated
using the accessory ccm 1 antecedence 1 command. Note that the San Jose Cisco Unified
Communications Manager server references the identifier advantage ahead specified.
Then, the DSP acreage contour is associated with the SCCP accumulation application the accessory profile
command. The annals XCODERouter1 advantage acclimated on Router1 assigns the name
XCODERouter1 to the profile. This name will be acclimated aback registering with Cisco
Unified Communications Manager and will be appropriate aback configuring the Cisco
Unified Communications Manager to point aback to the DSP resource. On Router2, the
register CFBRouter2 advantage is used, because this contour is a appointment bridge.
These commands are issued on both gateways, Router1 and Router2, as illustrated in
Examples 2-8 and 2-9.
Example 2-8 Configuring SCCP on Router1
110 Authorized Self-Study Guide: Cisco Voice over IP (CVOICE)
Router1(config)#sccp bounded FastEthernet 0/1
Router1(config)#sccp ccm 10.1.1.201 identifier 1 antecedence 1 adaptation 4.1
Router1(config)#sccp
Router1(config)#sccp ccm accumulation 1
Router1(config-sccp-ccm)#bind interface FastEthernet0/1
Router1(config-sccp-ccm)#associate ccm 1 antecedence 1
Router1(config-sccp-ccm)#associate contour 1
Router1(config-sccp-ccm)#register XCODERouter1
Example 2-9 Configuring SCCP on Router2
Router2(config)#sccp bounded FastEthernet 0/1
Router2(config)#sccp ccm 10.1.1.201 identifier 1 antecedence 1 adaptation 4.1
Router2(config)#sccp
Router2(config)#sccp ccm accumulation 1
Router2(config-sccp-ccm)#bind interface FastEthernet0/1
Router2(config-sccp-ccm)#associate ccm 1 antecedence 1
Router2(config-sccp-ccm)#associate contour 1
Router2(config-sccp-ccm)#register CFBRouter2
Unified Communications Manager Configuration
After the Cisco IOS agreement is complete, the media assets charge to be added to
Cisco Unified Communications Manager.
Continuing with the accepted example, a appointment arch is authentic in the Service,
Media Resource, Appointment Arch menu, as apparent in Figure 2-20.
Chapter 2: Considering VoIP Design Elements 111
Go to Service > Media Ability > Appointment Bridge.
Figure 2-20 Navigating to the Appointment Arch Agreement Screen
The anew added appointment arch now needs to be set up. Because the conference
bridge is application a PVDM2 deployed on an ISR, the Appointment Arch Blazon needs to be
Cisco IOS Enhanced Appointment Bridge, as illustrated in Figure 2-21.
After you baddest the actual type, specify the ambit declared in Table 2-14 and
illustrated in Figure 2-22.
Figure 2-21 Defining a Appointment Arch Type
Select Cisco IOS Enhanced Appointment Arch for PVDM2-based deployments.